Dust Explosion Suppression and Systems
Explosion Vent Panels
Explosion-proof mark | |
| Explosion Proof Mark | none |
Product specifications | |
| Operating Temperature | -40~+70 |
| Product source | Imported goods |
Description:
The explosion vent panels is an explosion-proof protection device for high vacuum pressure and volume, so that pressure waves are vented in a safe area to prevent the design strength of the container or equipment from being exceeded.
| Type | Measurements (mm)L*W | Av (m2) |
| BRP550x150 | 550x150 | 0.038 |
| BRP350x200 | 350x200 | 0.036 |
| BRP550x250 | 550x250 | 0.09 |
| BRP610x300 | 610x300 | 0.132 |
| BRP550x350 | 550x350 | 0.134 |
| BRP537x385 | 537x385 | 0.13 |
| BRP880x530 | 880x530 | 0.347 |
| BRP670x570 | 670x570 | 0.289 |
| BRP1100x600 | 1100x600 | 0.51 |
| BRP1000x666 | 1000x666 | 0.524 |
| BRP1198x995 | 1198x995 | 1.02 |
| BRP1000x1000 | 1000x1000 | 0.828 |
| BRP1100x1100 | 1100x1100 | 1.02 |
| BRP2000x1000 | 2000x1000 | 1.73 |
Explosion Suppression System
The chemical explosion suppression system continuously monitors the pressure or infrared radiation, and in the event of an explosion, rapidly releases the fire extinguishing solvent in the suppressor to prevent high pressure propagation caused by the explosion of combustible dust inside the equipment or the container, thereby preventing the container from being exceeded. Or the design strength of the device.
Technical specifications: fire retardant dust up to KST≦250 bar‧m/s
Fire extinguisher: sodium bicarbonate
Flameless Explosion Vent Valve
Technical Features:
• Suitable for melting products
• Max. Pred admissible: 0,5 barg
• Kstmax < 250 bar m/sec
• Pmax: 10 barg
• Working Temperature: -20ºC to 70ºC
• Casing built in: Carbon Steel, Stainless Steel or Aluminium
• ATEX Certification: LOM08ATEX7038X according to EN16009
The Flap Valve NOVEx
Casing built in carbon steel or stainless steel.Lamp Cover:
Lamp holder Size:Certification Unit:
▪Flap system.
▪Normally open operation.
▪Max. pressure drop up to 80% less than Normally Closed flap valves.
▪Sizes: from DN 71mm to DN 1000mm
▪Kst dust up to St2 Dust type IIIA, IIIB o IIIC
▪Pressure wave closes the flap before passing the flame
NOVEx
•Casing built in carbon steel or stainless steel.
•Max. range of dust concentration in the duct: 500 g/m³.
•No minimum flow needed to keep it open.
•Max. Pred of the vessel where explosion is originated:
•DN≤500 mm: 2 barg
•DN>500 mm: 1 barg
•Horizontal installation.
•Variable installation distance:
•DN ≤ 500mm: between 3 y 10 m.
•DN > 500mm: between 5 y 13 m.
•Possibility of two 90º bends
•No min. distance between valve and bends
•Max. flap opening angle of 60º.
Inerting System
The Inerting System INERMATIC optimize the consumption of inert gas, continuously analyzing the concentration of O2 and injecting automatically the necessary amount of inert gas.
Technical specifications: inert gas: N2 or CO2
Ambient temperature: -20~+40oC
Control interface: touch screen
Protection factor: IP54, IP65